Odroid HC4 Home Cloud with OLED 4GB RAM 1.8 GHz Quad Core Amlogic S905X3
The Odroid-HC4 features the 1.8 GHz Amlogic S905X3 ARM Cortex-A55 Quad-Core processor with Mali G31 MP2 Graphics Processing Unit just like the Odroid-C4. The Odroid-HC4 is a Home Cloud-based board. DDR4 4GB RAM is the memory on the board. The HC4 has an SPI 16MiB flash chip with Petitboot support.
Note: This HC4 version comes with the OLED.
What is new with Odroid-HC4
The Odroid-HC4 has a consistent SATA bridge solution (PCIe to SATA) as an alternative to USB3.0 to SATA. This way, 2x SATA storage docks are supported by HC4. This board has a transparent case with cutouts for ports and board interfaces.
Video Presentation of the Product
Specifications of Odroid-HC4 Home Cloud
Processor- Amlogic S905X3 12nm
- 32 KB L1 instruction cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
- 32 KB L1 data cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
- 512KB L3 data cache, 512 sets 16-way set associative, 4 processors share 64 byte lines
- Architecture: ARMv8-A with Crypto and Neon extensions
- Mali-G31 MP2 GPU (650MHz) 4x Execution Engines
- 1x RJ45 GbE LAN Port | backs 10/100/1000 Mbps
- RTL8211F Realtek Ethernet Transceiver
- Amber LED: 1000Mpbs connection DTI
- Green LED: 100Mpbs connection DTI
- 4GiB DDR4
- Low Power Design: 1.2Volt
- But width: 32-bit
- Data Rate: 2640 MT/s
- Grade: PC4-21333
-
1x Micro SD Slot (Compatible with both DS/HS mode and backs UHS-1 SDR104)
- 1x DC Power Jack: 5.5mm (negative / outer) and 2.1mm (positive / inner) diameter
- 14.5V ~ 15.5V DC Input
- 15V / 4A DC Power Adapter Recommended (Not Included)
- IDLE Mode: Approx. 5.88 W (when HHD is in Spin-Down)
- Active Mode: Approx. 15.59 W (while using SAMBA)
- Suspend Mode: Approx. 0.29 W
- Dimensions of HC4 Board: 90.5mm x 84mm x 25mm
- Weight of HC4 (including the case, fan, and heatsink): 280 grams
- 1x HDMI 2.0 Port with HDR, EDID, CEC | up to 4K @ 60Hz
- 1x HDMI Digital Audio Output
- A passive heatsink on the processing unit
- Dimensions: 40mm x 32mm x 10mm
- A Hydraulic Bearing Fan
- Maximum Rotations Per Minute (RPM): 4000 Rotations
- Air Pressure: 0.053 in H2O
- Air Flow: 4.3 CFM
- Current Rating: 100 mA
- Voltage Rating: 5V
- Noise Level: 23.9 dBA
- Connector and Wire: 1.25mm Pitch 4-Pin, 80mm
- Dimensions: 40mm x 40mm x 10.6mm
- SATA Connectors (x2)
- HOST USB 2.0 Port (x1)
- UART Serial Debug Console (x1)
- IR receiver for infrared remote control
- System Indicator LEDs
- BLUE (Flashes when Kernel is running)
- RED LED for PWR (DC Power Connected)
Odroid-HC4 Software Compatibility
Petitboot is adept to automatically locate the OS on the SSD, HDD, or SD Card. Meaning that in case SD-Card is not present, the Petitboot will use the attached SSD or the HDD to boot the Odroid-HC4 if the OS is installed on any of the storage units.
The already installed OS Image from Hardkernel is attuned with Debian and Ubuntu Operating Systems. Ubuntu or Debian Netboot installer can also be used.
The following versions of Linux Kernel are supported by Odroid-HC4:
- Mainline Kernel (unofficial) version 5.8 or higher
- Hardkernel Stock OS version 4.9.230 or higher
Articles Included
- 1x Odroid HC4 with OLED
Compatible Items (Not Included)
- 15V/4A Power Supply (Official Power Supply Recommended by Hardkernel)